Custom 1L Protection Atmosphere Inner Mixer
Product brief introduction
This internal mixer is made of imported all-alloy materials (no
need for spraying or electroplating), suitable for high-viscosity
and high-hardness powder metallurgy, ceramic powder,
titanium/aluminum alloy powder, and is suitable for the internal
mixing and refining of various raw materials.
Technical Data
| CF-1LQF | CF-3LQF | CF-5LQF |
| Effective mixing volume(L) | 1 | 3 | 5 |
Batch Feeding
(depending on material) | 2-5KG | 6-9KG | 10-15KG |
| Main Motor(KW) | 4 | 7.5 | 11 |
| Frequency Converter(KW) | 4 | Accept customization |
| Pressure Cylinder | ￠63 | ￠80 | ￠100 |
| Speed (front/rear) | 0 - 40/31r/ min | 0- 40/31r/min | 0- 40/31r/min |
| Heating Method | Electric heating | Electric heating | Electric heating |
| The Cooling Industry | Ventilation cooling | Water cooling | Water cooling |
| Pitch Diameter Of Screw Rod | 35mm | Accept customization |
| Weight(KG) | 1200 | 2080 | 2500 |
Product Superiority
1. The inner chamber can be fully open,easy to clean without any
dead ends.
2. By adopting PLC control system to connect the preset values and
the detection values,with intelligentoperation to discharge the
oxygen contect in positive pressure,and recharge inert gas
automatically.
3. With double atmosphere protection device,the mixing process is
in the condition of positive pressure.
Operating Principle
The two rotors in the mixing chamber rotate relative to each other
under a certain speed ratio, clamping the material from the feeding
port and bringing it into the roller gap to be squeezed and sheared
by the rotors. After passing through the roller gap, it hits the
sharp edge of the mixing chamber "W" and is divided into two parts,
respectively along the gap between the front and rear chamber walls
and the rotors and then returns to the top of the rotor. In the
closed mixing chamber, the material is strongly sheared and mixed
under certain pressure and temperature conditions, so that the
formula materials are fully dispersed and plasticized, so that the
formula can play the best effect.
Mixing System
The mixing chamber is "W" shaped, and adopts an "M" shaped lower
pressure cover to form a fully enclosed mixing space. The stirring
blade adopts a prismatic spiral design without dead angles, so that
the material can be sheared and dispersed to meet the physical
property requirements. The stirring blade is a hollow structure,
and the part in contact with the material is made of imported
all-alloy material (no spraying or electroplating is required),
which is wear-resistant, corrosion-resistant, not easy to stick to
the material, and has a long service life.
Technical Advantage
1. CFine's anti-leakage powder device adopts mechanical shaft seal
tightening technology and uses self-lubricating seal rings to keep
the seal rings in a compressed and sealed state during the mixing
process. The self-lubricating seal rings can further reduce the
wear of the mixing system and more effectively reduce the noise
such as whistling caused by leakage and poor sealing. It can
greatly improve the anti-leakage powder function, making cleaning,
color change and disassembly simpler and more convenient, and
reduce the pollution to the materials.
2. This machine adopts a through-type heating system, which heats
faster and transfers temperature more evenly, and the heating
efficiency is 50% higher than that of traditional heating plates.
It adopts a PLC program control system.
3. The internal structure of the mixing chamber adopts a complex
tube-belt design, which has good heat exchange and precise
temperature control. The rotor is cooled by water, which
effectively prevents sticky materials and controls the temperature
precisely, making the materials dispersed more evenly.
After-sales Service
During normal use, non-consumable parts are guaranteed for one
year. We provide on-site installation guidance and long-term
technical support.
Note: Electrical components and motors are imported from Taiwan and
foreign brands.
